KitchenAid Refrigerator Lights and Bulbs (2024)

Your Price

$11.73

interior drawers were off their rollers

pulled the washer out and replaces the top roller system on both sides and the replaced the weels and brackets on the bottom drwaer. however i had trouble putting the dish washer back correctly and had to call a repairman to adjust the dishwasher and alighn it to open and close properly. but i did do good inside. i feel it was easy and a success. thank you for having the supplies for us to attempt to repair it on our own. Read more...

Your Price

$16.32

Dryer was sqeaking loudly when running

I Looked on internet sites for this type of problem.
Most sites said the support rollers could cause this.
I found your site PartSelect and with help of your diagrams of the machine ordered the parts I thought were needed plus other parts that might cause the problem.
With machine torn down I replaced the rollers.
I had also ordered the main drive belt and idler assembly with the rollers and these also needed replacement. It is a good idea to order other suspect parts when doing this type of repair since you can return the parts not needed.
Your return policy is great.

Edward Brennan

Your Price

$183.67

Central light board flashed periodically then quit

I began by replacing the central light board by using a plastic non-marring wedge type tool slipping it between the housing and the retainers to release the latch like catch. Then I removed the lightboard and light cover assembly by depressing the latch like retainers for the two wire connectors. Installation was as simple as snapping the wires into the connectors and then pushing the lightboard and light cover assembly into place. One major note: I learned from a repairman that you cannot resolve the problem by simply replacing the central lightboard. you must replace all three lightboards, the two in the refrigerator and the one in the freezer because unless you can absolutely identify which board is causing the fault, it will continue to cause a problem on the main board and the lights will not work. Replacing the other two boards is the same as the central board. Additional comment to consider: I absolutely fail top see how this design of using three circuit boards for a simple light saves me anything; in fact after only 5 years it has cost me in excess of $400 (or 20% of the original cost of the unit) just in materials for a simple light--absurd, ridiculous design. If it burns out again I will have an appliance repairman install a simple 1950's design switch a small LED bulb which will probably last longer than the unit. Read more...

Your Price

$109.55

Freezer light out and refrigerator lights dim

I was not able to unplug the refrigerator because it is housed in a built-in. I removed the icemaker and following simple instructions from YouTube was able to pry the cover off the existing part. After a few gentle tugs, I disconnected the pinned wires from the old part. Connecting the new part was a little tricky but I managed with a little contorting. As soon as the pins connected the freezer light as well as the refrig lights came on. It took about 15 minutes to complete. Read more...

Your Price

$17.11

The door was crocked and wouldn't shut properly

Everything was easy. I read one of your other reviews and it gave me the confidence to try it myself. First i toke off the cap at the top of the door then the three screws. I lifted the door off so i could be sure the cam was my only problem then put the door back on. That took 5 mins. Then I got on the computer and ordered the parts i needed. Two days later the parts arrived and and i took the door off again. Then put the new cam on, applied a litle vasiline, put the door back on and forgot that i ever had a problem. Thanks for the help. Doug Arau Read more...

Your Price

$50.67

The piece that covered the light at the back of the fridge burnt a hole in the cover.

First I removed the cover...and then I slid the new piece in. It looks great and so easy a caveman could do it...lol Read more...

Your Price

$7.95

Both Upper Lights Burned Out Same Time

The holder is held in place with two screws. Once you have it unscrewed you can snap the old sockets out and replace them.

Ordered new sockets and presto, the lights work again.
They just snapped into the holder and the holder went up with two screws.
HINT: I did take a photo of the 4 electrical connectors AND labeled each one with a Sharpie 1, 2, 3, and 4 from left to right.

Your Price

$50.62

Broken drawer track, broken light lens, inoperative ice maker

The repairs were straight forward. The light lens and pan slide track were a simple matter of slipping the old out and installing the new. The door switch was a bit more tricky to remove. A quick check on the internet (googled the part number of the switch) to find the instructions for removal. Installation with simply the reverse. Read more...

Your Price

$14.79

Your Price

$70.72

Light Would Not Go On In The Refrigerator

First I removed the old lightbulb from the socket and replaced it with a new one to confirm that the bulb was not the problem. I then pryed the socket out with a flat-head screwdriver. I could tell that the socket was anchored in its hole with clips so it was relatively easy to pry it out. Once the socket was out, I disconnected the lead wires and ordered a replacement socket kit from Partselect. When the new one arrived, I reconnected the lead wires to it, snapped it back into its hole, screwed in a new lightbulb, and presto!! The light was back on with no further problem. Thank you, Partselect!! A $15.00 part saved me what probably would have been at least a $100. service call and heaven knows what the technician would have told me I needed!!! Read more...