Apologies for the simplistic question here.
I’m an owner/builder attaching 7/8-inch thick board-and-batten siding in southwest Wisconsin. Beneath it is Tyvek, then 3/4-inch horizontal shiplap, then 2×6 studs with dense-packed cellulose. I’m wondering what kind of fasteners to use.
At the top and bottom of the boards, where I know there are studs, I’ll use 3-inch screws. Then I’d like to nail the rest of the boards only into the sheathing, ideally with 1 5/8-inch spiral or ring shank nails. But so far I can’t find siding screws that short. If I use longer nails, they’ll penetrate into the cellulose, which I’m worried could create moisture issues in cold weather. Is that a valid concern?
Another option I’m considering is using 1 5/8 screws on the sides of the boards, which would be covered with the battens. This would be more expensive, but give more holding power and not penetrate into the cellulose.
Thanks for any advice.
~Joe
FAQs
Use galvanized, coated, or stainless wood or deck screws. Dark colored ones are less noticeable after staining. You will need at least 1-3/4” screws for the wide boards and at least 2-3/4” for the narrow battens. Boards should be screwed 2” from both the top and the bottom and then at least every 2' vertically.
How do you secure board and batten siding? ›
Starting at one corner of the house, place a board flush up against the wall and make sure it's plumb. When it is, secure the board by installing two nails at the top of the and two to the bottom of the board. Once it's secured, install two nails every 18”-24” along the board's length.
How is reverse board and batten siding attached? ›
For a reverse board-and-batten cladding, the thin battens are nailed onto the wall first. The wider boards are nailed over them, so the battens are behind the gaps.
What nails do I use for board and batten? ›
In order to attach, I first glued each board with liquid nails for extra security, and then I nailed the pieces in with a Brad Nailer. I highly recommend using a brad nailer, so the nails are almost invisible and it has a more seamless and high-quality look to it. I used 2 inch brad nails.
Do you nail or screw board and batten siding? ›
You can nail or screw board and batten siding in place based on the manufacturer's instructions. Nails are a common choice for wood siding, while screws are the more popular choice for vinyl, metal, and fiber cement, as these materials require predrilled holes in the siding.
What are the best siding fasteners? ›
Use only corrosion-resistant nails (aluminum, stainless or galvanized roofing.) Nails should have a minimum head diameter of 5/16". CertainTeed recommends the use of stainless steel nails or other corrosion-resistant fasteners when installing siding in coastal areas.
Does board and batten need strapping? ›
Strapping should be installed 16” on center. It is important to understand that there must be a gap left between the structure and the siding so that water and air can move as needed. In a case where board and batten are used, the house or structure needs to be double strapped.
What are the disadvantages of board and batten siding? ›
Cons
- Costly Upfront. One of the reasons homeowners tend to prefer lap siding over board and batten siding is its high upfront cost. ...
- Complex Installation. Unlike traditional lap siding that is installed using interlocking and overlapping mechanisms, board and batten siding is harder to install.
apart, battens should overlap by at least 1/2 in. With wider boards, increase batten overlap proportionately. While there are no set widths for board and batten siding, an attractive combination is 1×3 battens with 1×10 boards. Siding should be nailed to horizontal blocking lines or to furring strips.
What goes under board and batten siding? ›
Board-and-batten can be installed onto solid plywood or OSB sheathing, though if your sheathing is not solid, you will need to first attach horizontal furring strips. In general, you can expect to spend about a day installing 800 square feet of siding if you have a helping hand.
The installation of board and batten siding typically involves placing wider 'board' pieces of siding over a home's exterior wall and then covering the seams with narrower 'batten' pieces. It's a layered approach that can be done vertically or horizontally, depending on design preferences.
Should I use liquid nails on board and batten? ›
Apply liquid nails to the back of you boards and attach the board to the top of wall. Once you've attached the top horizontal board, do the same for the bottom horizontal boards. Use a level to make sure your boards are applied straight. Finally, fastening boards to wall using your nailer or hammer.
How do you nail green board and batten siding? ›
Boards want to cup one way so put the "hump" out and put one nail in the center. Jam them up tight and put the batten on so that the nail hits between the two boards. On wide boards (12" or wider) put 2 nails about 2 to 3 inches apart in the middle.
Do you nail or screw battens? ›
Nails are the correct fixing for nailing battens on.
What size nails for batten? ›
∎ B S 5534 'Code of practice for slating and tiling', states that the nails used for fixing tiling battens should generally have a shank diameter not less than 3.35mm. The nail is typically 65mm long to provide a minimum 40mm penetration into the rafter.
How do you hang things on a board and batten? ›
👉 Hanging Heavy Items on Board and Batten Vinyl Siding
For very heavy items, you may need to use screws or other fasteners that can provide a more secure hold. In this case, you'll need to pre-drill a hole and then insert the screw directly into the siding.
How do you nail board and batten without studs? ›
How do you attach board and batten to wall? This is a simple answer – it depends on the studs. If you hit a stud with your boards, use just 2″ nails and a nail gun. If you do not hit a stud, you will want to use construction adhesive along with the nails to make sure the boards are well attached to the wall.
